Editor Version ×

1.Easy to use and quick to get started

2.The process supports design scales of 300 devices or 1000 pads

3.Supports simple circuit simulation

4.For students, teachers, creators


1.Brand new interactions and interfaces

2.Smooth support for design sizes of over 30,000 devices or 100,000 pads

3.More rigorous design constraints, more standardized processes

4.For enterprises, more professional users

STD Seeeduino Ethernet

  • 3.5k
  • 0
  • 9

No Profile


Creation time: 2016-01-12 10:21:12
Update time: 2022-02-05 00:41:50
Introduction Seeeduino Ethernet is a compact and multifunctional development platform, which merges data logging and processing, device control and Ethernet communication together into one. It's armed with a MEGA328P chip and a Wiz5100: the former provides an Arduino controlling style and the latter provides TCP and UDP Ethernet communication ability. Plus integrated SD card module, it's convenient and neat for remote data logging, processing or transferring via network. In this version, we lowered the height of RJ45 to balance it with the headers. Besides, with an I2C and a UART Grove port populated,it's convenient to connect corresponding Grove modules to this board.4 ![enter image description here][1] Specification Voltage: 6.2-13V Current: 140-550mA Supported Card Type: Micro SD card(must be SanDisk), FAT/FAT32 (More than 2G is not guaranteed) Supported Connection: TCP/UDP Net Weight: 23±2g Ethernet jack: Standard RJ45 Demonstration We will test the Seeeduino Ethernet functions of writing or reading information from the SD Card and sending out A/D data to network. ![enter image description here][2] Step 1: Install the Hardware Firstly, install the hardware. We have two alternatives to plug in the power. Method 1: You can use one Passive PoE Cable Set to provide power and Ethernet connection at the same time like the picture below. ![enter image description here][3] Method 2: Use separate power cable and Ethernet cable. ![enter image description here][4] Step 2: Programing After hardware installation, here we continue to try the test code. This program is written to test the functions of writing or reading data from the SD Card and sending out A/D data to network. This demo code can be used as a test program as well as reference if you wanna explore more functions of the board. NOTICE: 1. All the ".h" file needed have been pre-installed in Arduino IDE(1.0). 2. Install a Micro SD card. Make sure the Micro SD card is not full and the format is FAT or FAT32. /* SD card read/write This example shows how to read and write data to and from an SD card file The circuit: * SD card attached to SPI bus as follows: ** MOSI - pin 11 ** MISO - pin 12 ** CLK - pin 13 ** CS - pin 4 Web Server A simple web server that shows the value of the analog input pins. using an Arduino Wiznet Ethernet shield. Circuit: * Ethernet shield attached to pins 10, 11, 12, 13 * Analog inputs attached to pins A0 through A5 (optional) created 18 Dec 2009 by David A. Mellis modified 4 Sep 2010 by Tom Igoe */ #include #include #include // Enter a MAC address and IP address for your controller below. // The IP address will be dependent on your local network: byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }; IPAddress ip(192,168,1,177); // Initialize the Ethernet server library // with the IP address and port you want to use // (port 80 is default for HTTP): EthernetServer server(80); File myFile; void setup() { Serial.begin(9600); Serial.print("Initializing SD card..."); // On the Ethernet Shield, CS is pin 4. It's set as an output by default. // Note that even if it's not used as the CS pin, the hardware SS pin // (10 on most Arduino boards, 53 on the Mega) must be left as an output // or the SD library functions will not work. pinMode(10, OUTPUT); // pinMode(4,OUTPUT); if (!SD.begin(4)) { Serial.println("initialization failed!"); return; } Serial.println("initialization done."); // open the file. note that only one file can be open at a time, // so you have to close this one before opening another. myFile = SD.open("test.txt",FILE_WRITE); // if the file opened or created okay, write to it: if (myFile) { Serial.print("Writing to test.txt..."); myFile.println("testing 1, 2, 3."); // close the file: myFile.close(); Serial.println("done."); } else { // if the file didn't open, print an error: Serial.println("error opening test.txt"); } // re-open the file for reading: myFile = SD.open("test.txt"); if (myFile) { Serial.println("test.txt:"); // read from the file until there's nothing else in it: while (myFile.available()) { Serial.write(myFile.read()); } // close the file: myFile.close(); } else { // if the file didn't open, print an error: Serial.println("error opening test.txt"); } // start the Ethernet connection and the server: Ethernet.begin(mac, ip); server.begin(); } unsigned char buff[6]; void loop() { EthernetClient client = server.available(); if (client) { // an http request ends with a blank line boolean currentLineIsBlank = true; while (client.connected()) { if (client.available()) { char c = client.read(); // if you've gotten to the end of the line (received a newline // character) and the line is blank, the http request has ended, // so you can send a reply if (c == '\n' && currentLineIsBlank) { // send a standard http response header client.println("HTTP/1.1 200 OK"); client.println("Content-Type: text/html"); client.println(); // output the value of each analog input pin for (int analogChannel = 0; analogChannel "); buff[analogChannel] = analogRead(analogChannel); } break; } if (c == '\n') { // you're starting a new line currentLineIsBlank = true; } else if (c != '\r') { // you've gotten a character on the current line currentLineIsBlank = false; } } } // give the web browser time to receive the data delay(1); // close the connection: client.stop(); myFile = SD.open("test.txt", FILE_WRITE); if (myFile) { Serial.println("test.txt:"); for (int analogChannel = 0; analogChannel
Design Drawing
schematic diagram
1 /
1 /
ID Name Designator Footprint Quantity
1 13pF C9,C16,C22,C23 0603 4
2 DC-044-AH J3 DC-404 1
3 78M05 U8 TO252 1
4 LD1117-3.3 U11 SOT-223 1
5 1k R12,R13,R3,R4,R1,R10,R11,R16 0603 8
6 RED RST LED-0603 1
7 GREEN PWR,L LED-0603 2
8 10k R14,R15 0603 2
9 100nF C7,C10,C24,C28,C5,C15,C17,C1,C2,C3 0603 10
10 1000v_1nF C4 C1206 1
11 16MHz X4 2P-SMD-5X3.2 1
12 25MHz X2 2P-SMD-5X3.2 1
13 RJ45-MJ88-BX11-RVSL2 J8 RJ45-MJ88-BX11-RVSL2 1
14 10v_10uF C8,C14 AVX-A 2
15 49.9_1% R5,R2,R6,R8 0603 4
16 W5100 U1 SQFP80 1
17 12.3k-1% R7 0603 1
18 10nF C12 0603 1
19 female PB,PD 8P-2.54 2
20 YELLOW TX,RX LED-0603 2
21 1M R9 0603 1
22 SD card holder J1 9P-SMD-W-RING 1
23 TWIG-4P-2.0 UART,I2C 4P-2.0 2
24 10v_10uF C29 0805 1
25 M7 D4,D1 D2010 2
26 PPTC-500mA F3 1206 1
27 ATmega328-20AU U2 TQFP32 1
28 2.54-2x3p male ICSP 2X3P-2.54 1
29 female PC,PR 6P-2.54-6535MIL 2
30 HX1198NL U3 SOIC16-9.53 1
31 75 R19,R26 0603 2
32 25v_47uF C6 AVX-C 1
33 male-90degree J6 6P-2.54-6535MIL 1
34 2P button RESET 2P-7.62X3.56-90D 1
35 74ACT245 U4 TSSOP20 1
36 DNP P1,PD2 2P-SMD-1.78X1.27 2
37 10uF C11,C13 0805 2
38 DNP R17 0603 1


Project Attachments
Project Members
Target complaint
Related Projects
Change a batch
Add to album ×


reminder ×

Do you need to add this project to the album?


周一至周五 9:00~18:00
  • 0755 - 2382 4495
  • 153 6159 2675


周一至周五 9:00~18:00
  • 立创EDA微信号


  • QQ交流群


  • 立创EDA公众号