© 2024 EasyEDA Some rights reserved ISO/IEC
Editor Version
×
recommended
Pro Edition
Brand new interactions and interfaces
Smooth support for design sizes of over 3W
devices or 10W pads
More rigorous design constraints, more
standardized processes
For enterprises, more professional users
Std Edition
Easy to use and quick to get started
The process supports design scales of 300
devices or 1000 pads
Supports simple circuit simulation
For students, teachers, creators
Ongoing
STD IRS2092 for GERBER_OLD
IRS2092 for GERBER_OLD
License
Public Domain
License: Public Domain- 10
Update time：
2021-12-21 01:50:29
Creation time：
2020-12-31 14:57:23
Description
Description
Усилитель мощности звуковой частоты класса D построенный на базе микросхемы IRS2092. Выходная мощность около 250-300 ватт на нагрузка 4 Ома, рекомендованная рабочая частота 350-400 кГц, присутствует защита от короткого замыкания в нагрузке. Схема рассчитана на работу с полевыми транзисторами IRFB5615, при использовании других транзисторов необходимо пересчитать некоторые номиналы. Усилитель при правильной сборке работает сразу, требуется только настройка желательной рабочей частоты переменным резистором. Для питания Усилителя необходим источник питания с силовым двухполярным выходным напряжением 35-50 вольт (допускается до 55 вольт) с силой тока 2.4 Ампер на один канал, и слаботочное напряжение 12 вольт для питания логики.
Дроссель намотан на сердечнике Т106-2 проводом 1 мм количество витков 56
Class D audio frequency power amplifier based on the IRS2092 chip. Output power about 250-300 watts per 4 Ohm load, recommended operating frequency 350-400 kHz, there is protection against short circuit in the load. The circuit is designed to work with field-effect transistors IRFB5615, when using other transistors it is necessary to recalculate some denominations. The amplifier at the correct assembly works at once, only adjustment of desirable operating frequency by the variable resistor is required. The power supply of the Amplifier requires a power supply with a power bipolar output voltage of 35-50 volts (up to 55 volts is allowed) with a current of 2.4 Amperes per channel, and a low-voltage voltage of 12 volts to power the logic. The choke is wound on the core T106-2 wire 1 mm number of turns 51
Дроссель намотан на сердечнике Т106-2 проводом 1 мм количество витков 56
Class D audio frequency power amplifier based on the IRS2092 chip. Output power about 250-300 watts per 4 Ohm load, recommended operating frequency 350-400 kHz, there is protection against short circuit in the load. The circuit is designed to work with field-effect transistors IRFB5615, when using other transistors it is necessary to recalculate some denominations. The amplifier at the correct assembly works at once, only adjustment of desirable operating frequency by the variable resistor is required. The power supply of the Amplifier requires a power supply with a power bipolar output voltage of 35-50 volts (up to 55 volts is allowed) with a current of 2.4 Amperes per channel, and a low-voltage voltage of 12 volts to power the logic. The choke is wound on the core T106-2 wire 1 mm number of turns 51
Design Drawing
Design Drawing
schematic diagram
（
1
/
）
PCB
（
1
/
）
The preview image was not generated, please save it again in the
editor.
Unfold
Project Members
Project Members
9
10
Collect to album
Target complaint
Related Projects
Change a batch
Loading...
Comment
Add to album
×
Loading...
reminder
×
Do you need to add this project to the album?