Editor Version ×
Standard

1.Easy to use and quick to get started

2.The process supports design scales of 300 devices or 1000 pads

3.Supports simple circuit simulation

4.For students, teachers, creators

Profession

1.Brand new interactions and interfaces

2.Smooth support for design sizes of over 5,000 devices or 10,000 pads

3.More rigorous design constraints, more standardized processes

4.For enterprises, more professional users

Ongoing

STD WiFi Enabled 2.4" Touch Screen with SD Reader

WiFi Enabled 2.4" Touch Screen with SD Reader

Project tags

License

TAPR Open Hardware License

License: TAPR Open Hardware License

Mode:

Mode

Editors' pick

Editors' pick

  • 7.1k
  • 2
  • 13
Update time: 2022-01-21 11:31:20
Creation time: 2019-09-13 14:16:43
Description

Description

# Simple yet powerfull! ![P1010032.JPG](//image.easyeda.com/pullimage/AX4EffUg9uGuqlnloEiUsM0rCtBuGwGNRvkl16oE.jpeg) This board provides solid connection between Wemos D1 mini (ESP8266) and 2.4" TFT ILI9341 XPT2046 SPI Display (TJCTM24024-SPI). The main goal is to build cheap wi-fi enabled display with touch interface for use in various IoT projects. Display communicates with ESP8266 via SPI (display, touch and SD card reader). Displays interrupt is connected do D0 pin allowing for waking up ESP8266 from Deep Sleep state. LCD LED backlight is driven via P-Channel MOSFET via D3 pin (high side transistor switch). Out of the box backlight is connected to 3V3. In order to drive backlight you need to cut J1 jumper and populate Q1 MOSFET (FDV304P) and R1 restistor (10k). Additional header may be used as general purpose UART, I2C, One Wire or Analog In. Pin order allow to directly solder BME280 module. Also we put I2C connector in Nettigo PSIIC form factor (compatible with SparkFun Qwiic & Adafruit STEMMA QT). ![PCB1843.png](//image.easyeda.com/pullimage/1Xb4yo25LF2mYr5aTE6y7kAauV2zGfTbmepgqAL9.png) ## Pinout - Standard ESP8266 SPI interface: - SCK - D5 - MISO - D6 - MOSI - D7 - LCD Chip Select - D8 - LCD D/C - D1 - LCD Reset - RST - LCD Backlight (via MOSFET) - D3 - Touch Chip Select - D2 - Touch IRQ - D0 - SD Card Reader Chip Select - D4 - I2C SCL / UART RX - RX - I2C SDA / UART TX - SDA ## Powering up the board - directly from micro USB, or - feeding 3.3V to 3V3 pin, or - feeding ~5V to 5V pin (voltage depends on what LDO is in your Wemos. Usually 4-6V is save value)
Design Drawing

Design Drawing

schematic diagram
1 /
PCB
1 /
The preview image was not generated, please save it again in the editor.
Project Attachments

Project Attachments

Empty
Project Members

Project Members

Target complaint
Related Projects
Change a batch
Loading...

Comment

Add to album ×

Loading...

reminder ×

Do you need to add this project to the album?

服务时间

周一至周五 9:00~18:00
  • 0755 - 2382 4495
  • 153 6159 2675

服务时间

周一至周五 9:00~18:00
  • 立创EDA微信号

    easyeda

  • QQ交流群

    664186054

  • 立创EDA公众号

    lceda-cn