Editor Version ×
Standard

1.Easy to use and quick to get started

2.The process supports design scales of 300 devices or 1000 pads

3.Supports simple circuit simulation

4.For students, teachers, creators

Profession

1.Brand new interactions and interfaces

2.Smooth support for design sizes of over 5,000 devices or 10,000 pads

3.More rigorous design constraints, more standardized processes

4.For enterprises, more professional users

Ongoing

STD MaxPCB4E

License: CC-BY-NC-SA 3.0

Mode: Editors' pick

  • 1.4k
  • 0
  • 2
Update time: 2023-12-30 13:22:36
Creation time: 2022-11-30 13:20:10
Description

For my OnStep telescope mount controller (visit my [group][1] for more information.)

This design is built around the Teensy4.1 processor (available on Amazon, PJRC, etc.) It has 8MB of flash, runs at 600MHz, and has a fast double precision capable floating point unit.  The T4.1 is the fastest/most capable OnStep supported MCU.  It also has an W5500 Ethernet module (puts the Ethernet RJ45 port on the front panel) and a socket for a Teensy3.2 or 4.0 to run OnStepX's Smart Web Server.  There is a bit more soldering necessary than with the MaxPCB4, but this avoids the rather difficult to assemble Ethernet adapter board of eariler versions.  Most components needed to build one of these can be obtained from EasyEDA/LCSC and eBay.

**Note: This design is for non-commercial use only (see License terms, CC-BY-NC-SA 3.0)**

This controller includes the following features:

* Power: Coaxial power jack, fuse, and power switch connection.
* Stepper drivers: Four, one for RA/Azm, one for Dec/Alt, one for a focuser, and one for a rotator/second focuser. It's designed to support full control (microstep mode etc.) of older StepStick drivers as well as TMC SPI ones, in all four sockets. All stepper motor connections are available on RJ jacks at the PCB back (screw terminals are optional.)
* Ethernet: SWS running on the Teensy4.0 with the W5500 Ethernet module sitting above Teensy4.1 so the RJ45 jack is on the front panel.
* Micro USB port built into the Teensy4.1.
* Status LED.
* Mini speaker for alert buzzer.
* DB15 15 pin D-Sub connector: primary external I/O for Gnd, +3.3V, 5V, two Home Switches, PEC, PPS, I2C, the Serial1 port, and two channels of A/B encoder inputs.
* 3.5mm stereo mini jack: secondary external I/O for Limit Switches and Reticle.
* RJ12 Modular connector: ST4 guider interface (with optional 5V power.)

---

Changes relative to MaxPCB3.6:

General use of SMT components to keep soldering to a minimum as EasyEDA now makes this easy to order/low cost.

Design allows use of readily available TMC2209 drivers, they have the best performance/cost.

Removed DS3231 RTC module in favor of using a battery and Teensy4.1 built-in RTC.  This makes room for plugging USB into the WeMos D1 Mini while operating and/or using the ESP32 based WeMos D1 Mini boards.

The following pins have changed…

* PIN34 M0_1 was changed to MISO (Teensy RX8, forms a bus for TMC2209 RX/PDN-UART pins.)
* PIN35 M1_1 was changed to M2_1 (Teensy TX8, FYSETC v3.1 TMC2209 TX pin.)
* PIN36 M2_1 was changed to M1_1 (swapped for above.)
* PIN37 MISO was changed to M0_1 (swapped for above.)

---

History
- Version4.0 - First release

  [1]: https://groups.io/g/onstep

Design Drawing
schematic diagram
1 /
PCB
1 /
The preview image was not generated, please save it again in the editor.
ID Name Designator Footprint Quantity
1 CR2032-BS-6-1 B1 BAT-TH_CR2032-BS-6-1 1
2 100nF C10,C11,C12,C13,C6,C7,C9 C0402 7
3 SS310_C85658 D1 DO-214AC_L4.3-W2.7-LS5.3-RD 1
4 PJ-325M/3.5MM J2 AUDIO-TH_PJ-325C 1
5 19-217/GHC-YR1S2/3T LED1 LED0603-R-RD 1
6 19-213/Y2C-CQ2R2L/3T(CY) LED2 LED0603-R-RD 1
7 4.7K R1,R2,R15,R16,R17,R18 R0603 6
8 2.4K R3,R5,R7,R8,R9,R10,R11,R12,R13,R14 R0603 10
9 240 R4 R0805 1
10 1kΩ R6 R0603 1
11 100uF C1,C2,C3 CAP-SMD_BD8.0-L8.3-W8.3-RD 3
12 47uF C4,C5 CAP-SMD_BD5.0-L5.3-W5.3-RD 2
13 330nF C8 C0805 1
14 DC005-2.0MM DC1 DC-IN-TH_DC005 1
15 XF-506P FH1 FUSE-TH_XF-506P 1
16 M2545V-02P J1 CONN-TH_M2545V-02P 1
17 1x3 Header J8,J9 1X3 HEADER 2
18 1x6 Header J3 1X6 HEADER 1
19 W5500-MINI_V1.1_EVB U10 W5500-MINI 1
20 TEENSY_3.2_BASIC U12 TEENSY_3.2_BASIC 1

Unfold

Project Attachments
Empty
Project Members
Related Projects
Change a batch
Loading...
Add to album ×

Loading...

reminder ×

Do you need to add this project to the album?

服务时间

周一至周五 9:00~18:00
  • 0755 - 2382 4495
  • 153 6159 2675

服务时间

周一至周五 9:00~18:00
  • 立创EDA微信号

    easyeda

  • QQ交流群

    664186054

  • 立创EDA公众号

    lceda-cn