Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is not supported at present. Please extend your EasyEDA usage duration and try again.
This Zigbee Module adopts CC2530 IC as the Transmitting and Receiving chip, which is System-On-Chip solution for 2.4Ghz IEEE 802.15.4 and Zigbee Application .
The CC2530 combines the excellent performance of a leading RF transceiver with an industry-standard enhanced 8051 MCU, in-system programmable flash memory, 8-KB RAM, and many other powerful features. The CC2530 comes in four different flash versions: CC2530F32/64/128/256, with 32/64/128/256 KB of flash memory, respectively. The CC2530 has various operating modes, making it highly suited for systems where ultralow power consumption is required. Short transition times between operating modes further ensure low energy consumption.
Combined with the industry-leading and golden-unit-status ZigBee protocol stack (Z-Stack) from Texas Instruments, the CC2530F256 provides a robust and complete ZigBee solution.
Combined with the golden-unit-status RemoTI stack from Texas Instruments, the CC2530F64 and higher provide a robust and complete ZigBee RF4CE remote-control solution.
Features:
RF/Layout
2.4-GHz IEEE 802.15.4 Compliant RF Transceiver
Excellent Receiver Sensitivity and Robustness to Interference
Programmable Output Power Up to 4.5 dBm
Very Few External Components
Only a Single Crystal Needed for Asynchronous Networks
6-mm × 6-mm QFN40 Package
Suitable for Systems Targeting Compliance With Worldwide Radio-
Frequency Regulations: ETSI EN 300 328 and EN 300 440 (Europe),
FCC CFR47 Part 15 (US) and ARIB STD-T-66 (Japan)
Low Power
Active-Mode RX (CPU Idle): 24 mA
Active Mode TX at 1 dBm (CPU Idle): 29 mA
Power Mode 1 (4 µs Wake-Up): 0.2 mA
Power Mode 2 (Sleep Timer Running): 1 µA
Power Mode 3 (External Interrupts): 0.4 µA
Wide Supply-Voltage Range (2 V–3.6 V)
Microcontroller
High-Performance and Low-Power 8051 Microcontroller Core
With Code Prefetch
32-, 64-, 128-, or 256-KB In-System-Programmable Flash
8-KB RAM With Retention in All Power Modes
Hardware Debug Support
Peripherals
Powerful Five-Channel DMA
Integrated High-Performance Op-Amp and Ultralow-Power Comparator
IEEE 802.15.4 MAC Timer, General-Purpose Timers
(One 16-Bit, Two 8-Bit)
IR Generation Circuitry
32-kHz Sleep Timer With Capture
CSMA/CA Hardware Support
Accurate Digital RSSI/LQI Support
Battery Monitor and Temperature Sensor
12-Bit ADC With Eight Channels and Configurable Resolution
AES Security Coprocessor
Two Powerful USARTs With Support for Several Serial Protocols
21 General-Purpose I/O Pins
(19 × 4 mA, 2 × 20 mA)
Watchdog Timer
Development Tools
CC2530 Development Kit
CC2530 ZigBee Development Kit
CC2530 RemoTI Development Kit for RF4CE
SmartRF Software
Packet Sniffer
IAR Embedded Workbench Available
APPLICATIONS
2.4-GHz IEEE 802.15.4 Systems
RF4CE Remote Control Systems (64-KB Flash and Higher)
ZigBee Systems (256-KB Flash)
Home/Building Automation
Lighting Systems
Industrial Control and Monitoring
Low-Power Wireless Sensor Networks
Consumer Electronics
Health Care
Forked project will be set private in personal workspace. Do you continue?
Clone
Project
The Pro editor is about to be opened to save as. Do you want to continue?
private message
Send message to felectronet
Delete
Comment
Are you sure to delete the comment?
Report
Zigbee CC2530 Module copy
No Profile
Announcer: felectronet
Creation time: 2019-01-22 15:38:42
Published time:
2019-01-22 15:38:43
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
*
Report type:
Please select report type
*
Report reason:
Please fill in the reason for your report and the content is 2-1000
words
*
Upload image:
+
Upload image
*
Email address:
Please fill in your email address
Report
Submitted successfully! The review result can be viewed in the personal
center, review notification.
Kind tips
Your EasyEDA usage duration is brief. In order to avoid advertising information, this action is
not supported at present. Please extend your EasyEDA usage duration and try again.
Share
Project
Copy
Copy
Scan the QR code and open it on the mobile terminal